Ross Forged Pistons Option Forged Scat Rods 99-07 Mopar 4.7L V8

  • Model: Ross 47ROSS Mopar 4.7L Pistons
  • Shipping Cost: 29.95 shipping
  • 1Dropships direct from manufacturer
  • Manufactured by: Ross Pistons

Starting at: $799.95

Please Choose:

Addituonal Options:














Basic Options:











Combo Deals:







Add to Cart:
Description:

NOTE: These pistons are made to be used with our AIR RAM PERFORMANCE SCAT RODS! They will NOT work with the factory RODS!!! 5x Sets in stock of (.040 10:1cr) with NA Low boost ring pack.

For our best deal price please select in the drop down menu the following option: a) ** BEST DEAL ** 10:1cr / +.040 bore - (No coatings) Skip to select rings AIR RAM PERFORMANCE brings you the ONLY 4.7L aftermarket pistons available ANYWHERE! Not only that but YOU have options as well. Drawing on nearly 30 years of piston design and manufacturing for all forms of motor sports, ROSS Racing Pistons has met the continual need for the most advanced forged pistons in the racing industry.

Details: **IMPORTANT**

Due to constant increases in material cost we have been forced to narrow down our piston options. Ross no longer is offering us the discounts on our one off pistons as they have over the years.

Due to its popularity, we have narrowed down our best deal Ross pistons to +.040 @10:1cr. These will be our "BEST PRICE" piston as we purchase these in bulk. With that said, anything other than +.040 @10:1cr will be made to order and will have additional cost to them. Unfortunately coatings are NOT available on these "BEST PRICE" pistons and will raise the cost to that of the one off production piston sets. We put up a good fight however we lost and are forced to limit our discounted options. We can still make any piston combination you like, however there will be additional cost to these custom sets.

Have your engine checked by your machine shop for MAX "SAFE" bore. Planning on building a High output 4.7L engine? Wanting to SAFELY run 100+ shot of Nitrous on your 4.7L? How about supercharge your 4.7L with over 10PSI of boost.... If you answered YES to any of the above then you need to replace your weak factory pistons with these FORGED Ross pistons.

Shown in our picture you can see our CUSTOM Ceramic coated pistons that have received the top of the line coatings.

* EPC108 - CERAMIC THERMAL BARRIER COATING IS APPLIED TO THE TOP OF THE PISTON ONLY. THIS COATING IS ESPECIALLY RECOMMENDED FOR TURBOCHARGED ENGINES.

* EPC100T - BLACK SKIRT COATING IS SIMILAR TO HARD ANODIZING WITH A TEFLON SEAL ON THE SKIRTS & IS VERY DENSE TO INCREASE PISTON SKIRT LIFE. ALL SURFACES OF PISTON ARE COATED.

* EPC102 - HARD SKIRT COATING WITH TEFLON SEAL & THERMAL BARRIER TOPS BY COMBINING EPC100T & RRC108 THE PISTON HAS THE ULTIMATE TOP & SKIRT PROTECTION. IT IS IDEAL FOR TURBOCHARGED ENGINES.

Here we have put together the KIT to help you run RELIABLE HP through your 4.7L ENGINE. Your stock pistons are a weak link and are bad choice for a performance build. Our ROSS postons will allow you to push the limits of your 4.7L engine.

These kits are priced with your choice of Pistons (FLAT/DOME/DISH) & Wrist Pins. This piston kit comes with everything you need as far as pistons go. RINGS NOT INCLUDED but can be added to the order. You can use these pistons on your stock Rods or an after market forged Rods. Your Stock Pistons only have 1/8 of an inch between the piston top and the top ring. This is VERY bad if you want to run Boost or any decent amount of Nitrous "SAFELY" without worrying about overheating and seizing the top ring.

Rest assured that ROSS has you covered.

Custom pistons are not returnable for refund or credit regardless of circumstances, unless the customer submitted a written purchase order and pistons do not meet the requirements of the written purchase order. Do not attempt to install ROSS Racing Pistons before reading the instructions. ROSS Racing Pistons reserves the right to make changes in design, materials and specifications, or to make product changes without incurring liability or obligation with respect to similar products previously manufactured.

Modifications:

**NOTES:

1) 11:1 Pistons are not a "TOSS IN, BOLT ON PISTON" your machine shop will need to do the math and verify piston to valve/head clearance. You need to verify PISTON to HEAD/valve clearance and insure you have the proper clearances. Selecting the proper head gasket thickness will be key.

Dropships direct from manufacturer.

Item Photo


This product was added to our catalog on Thursday 05 March, 2020.

Copyright © 2024 3rd Strike Performance
Mobile Website by: Manor Media Group